What type of chimney do I need for my stove?

You have decided on a wood-burning stove and now need to find out if you can connect it to your chimney?

Or, on the contrary, are you building a new house, only planning a chimney, and would like to know which type of chimney you need for your stove?

In both cases, one important rule applies:

The oven and chimney must work together as a system.

It is not enough that the flue pipe “fits into the opening in the chimney”. What is crucial are the diameter, height and construction of the chimney, its draft, the type of connection, the characteristics of the specific stove and the structural conditions themselves.

The good news is that you don’t have to be a chimney sweep to know what to look for when choosing a stove.

A chimney is not just a pipe for venting smoke.

The chimney’s function is not only to vent exhaust gases from the house.

The chimney also produces move, which helps to remove exhaust gases from the device and influences the air supply and the combustion process.

If the chimney and stove are not properly aligned, problems can occur even with otherwise high-quality stoves.

Therefore, it is a mistake to choose a device solely based on appearance and performance and only deal with the chimney after delivery.

What is a chimney flue?

Very easy:

The hot exhaust gases in the chimney rise upwards, creating a chimney draft.

The actual strength of the chimney draft depends on a number of factors – for example, the height and cross-section of the chimney, the temperature of the exhaust gases, the external conditions, the design of the exhaust gas path and the characteristics of the respective appliance.

And just as there could be a problem insufficient thrustExcessive tensile force may also be unsuitable.

Certain ovens have conditions specified by the manufacturer under which they should function properly.

Therefore, one cannot simply say:

“The higher the chimney and the stronger the draft, the better.”

What diameter should my chimney have?

This is a very common misunderstanding.

Information about ovens can be found, for example, in the technical data:

Exhaust pipe diameter: 150 mm

This is the diameter of the flue outlet on a particular stove.

This does not automatically mean that only the following data is needed for chimney planning:

“I need to have a chimney 150 mm.”

The suitability and dimensioning of the chimney are assessed based on the specific appliance and the entire exhaust gas path.

The diameter of the flue pipe is therefore a very important factor in the selection and connection of the stove, but The correct chimney is not determined solely by a number on the stove outlet..

I have a chimney of type 150 mm. Do I need to buy a stove with a matching flue pipe of type 150mm?

Not necessarily, but this is precisely where improvisation is out of place.

Different diameters can be solved technically in some cases, but it is not correct to automatically assume that buying a reducer will solve the problem.

Any change to the cross-section and any design of the exhaust pipe can affect the exhaust flow.

Therefore, if you already have a chimney and are choosing a new stove, check the suitability of a particular combination. before purchasing the device.

What is a flue pipe and what is a chimney?

These terms are often confused.

smoke extraction is the part that connects the stove to the flue pipe – typically the visible pipe that leads from the stove to the connection point.

chimney is a structure through which the flue gases are then safely vented over the building.

The point where the smoke vent connects to the chimney is called … sop.

Therefore, when choosing a stove, not only the chimney itself is important, but also… How do I connect the stove?.

Smoke vent at the top or the back?

Depending on the model, wood-burning stoves can have the following features:

  • upper outlet,
  • rear outlet,
  • Optionally with outlet at the top or rear.

If you already have a flue in your chimney, its position can significantly influence the choice of stove and the type of installation.

Therefore, we recommend that before ordering you not only check the diameter of the exhaust pipe, but also:

the height of the rear outlet axis, the overall dimensions of the stove and the distance of the stove from the chimney.

This is precisely the detail that is easily overlooked when purchasing and becomes very important during installation.

How tall does the chimney need to be?

Unfortunately, there is no universally valid number that applies to all stoves and all houses.

The height of the chimney affects the draft, but the resulting behavior also depends on other parameters.

Furthermore, it is important to distinguish between the overall height of the chimney and its height. effective height.

Therefore, it is not advisable to choose a stove solely based on the rule:

“I have a chimney that is X meters high, so this will work.”

For a specific installation, it is necessary to assess the chimney together with the requirements of the chosen device.

Can a chimney be too big?

Yes, even an unnecessarily large cross-section is not automatically an advantage.

Exhaust gases in an incorrectly sized chimney can behave differently than required by a particular appliance. This can lead to problems with draft, exhaust gas temperature, or the formation of condensation and deposits.

Therefore, this does not apply here either:

“The bigger the chimney, the better.”

The chimney should appropriately dimensioned for the respective device and operating conditions.

What if I have an old brick chimney?

An old chimney does not automatically mean that it can no longer be used.

However, it cannot be assumed that it will be suitable for a new oven without modifications, just because the oven has been connected to it for the last thirty years.

Before installing a new device, it is necessary to check its condition and suitability.

Depending on the situation, repairs, insert work, or other solutions may be necessary.

This must be assessed by an expert based on the actual condition of the chimney.

What is meant by chimney lining?

During the lining process, a suitable chimney pipe is inserted into the existing chimney opening.

It can be used, for example, when rebuilding an older chimney or adapting it to a new appliance.

However, this does not mean that every old chimney automatically needs to be lined.

The necessity and the appropriate method of modification depend on the condition of the respective chimney and the requirements of the connected device.

What if I only build one chimney?

This is indeed a very good situation – you have the opportunity to design the chimney and stove together.

The ideal approach is not:

First you build a chimney and then, a few months later, you find a stove that can be connected to it.

It’s better to know at least this during the design phase. What type of device and approximate parameters would you like to use?.

Based on this, the chimney, the position of the flue, the location of the stove and any external combustion air supply can be adequately taken into account.

➡️ [Kdy potřebuji externí přívod vzduchu?]

What if I already have a chimney?

Then we recommend that you at least find out the following:

  • Type and condition of the chimney,
  • Ventilation opening size or diameter,
  • effective height
  • the position and size of the trachea,
  • possible lining
  • Connection options for exhaust pipes,
  • Information on the chimney draft, if available.

This data can be used to significantly refine the selection of the oven.

If you don’t know the condition of your chimney, it’s advisable to have it checked first rather than blindly choosing a device.

Isn’t it enough to choose a stove with the same flue pipe diameter?

That’s not enough.

The diameter of the flue pipe is one of the important parameters, but other data also determine the suitability of the entire combination.

When choosing an oven, you should also pay attention to the required draft and other technical data from the manufacturer.

And of course, correct execution must not be forgotten.

Even a perfectly functioning chimney cannot change the fact that you have bought an unnecessarily powerful stove for a small, well-insulated room.

➡️ [Jaký výkon kamen potřebuji?]

What about the air supply?

The chimney directs the flue gases outside.

The air required for combustion must also enter the oven. come from somewhere.

Therefore, there is a close relationship between the chimney and the combustion air supply.

Particular attention should be paid to modern, airtight houses, houses with controlled ventilation, and rooms where other devices can create negative pressure.

➡️ [Kdy potřebuji externí přívod vzduchu?]

Can anyone tell me if my chimney is suitable?

The final assessment of a particular exhaust path is the responsibility of an expert who knows the actual condition of the chimney and the parameters of the connected device.

And this is not a formality.

We can explain the operating principles online and help you choose an oven based on technical parameters. However, without knowledge of the exact exhaust path, it cannot be confirmed with certainty that a particular stove will function properly on a particular chimney.

If you are unsure, we recommend that you consult a chimney sweep before ordering the oven.

This will save you from a much more expensive solution once the stove is installed at home.

So what should you find out before buying a stove?

If you already have a chimney, prepare it if possible:

  • Diameter or size of the chimney vent,
  • effective height of the chimney,
  • Condition and construction of the chimney,
  • diameter of the trachea
  • the height and position of the chimney,
  • Information about a possible chimney lining,
  • Available chimney draft data.

Then compare the selected ovens:

  • Exhaust pipe diameter
  • Top or rear outlet
  • Height of the rear exhaust axis,
  • required chimney draft
  • Manufacturer’s technical requirements.

Repair the chimney before transporting the stove.

If you should remember one thing from this page, let it be this:

First, check whether the selected stove is suitable for your chimney. Only then should you order it.

A stove is not a standalone piece of furniture.

The following elements are part of the system:

Oven → Combustion air → Flue pipe → Chimney.

And all the parts have to work together.

Choose an oven based on its technical specifications.

If you already know the parameters of your chimney, the selection process will be much easier.

In our offer you can filter stoves according to technical features and select, for example, according to the required heating output, the flue pipe diameter, the external air supply and other parameters.

[Vybrat krbová kamna podle parametrů]


Frequently Asked Questions

What diameter should the chimney for my stove have?

The stove’s output alone is not sufficient to reliably determine the optimal chimney size. Rather, the specific parameters of the appliance and the entire flue system must be considered. While the diameter of the flue pipe is an important indicator, it does not, on its own, constitute a complete chimney design.

I have a chimney 150 mm. Can I connect a stove to a flue pipe 120 mm?

Different dimensions can sometimes be technically resolved, but the suitability of a particular connection cannot be determined solely based on these two figures. The entire exhaust path and the appliance’s requirements must be taken into account.

Can I reduce or increase the size of the exhaust pipe using a reducer?

The presence of a suitable reducer does not guarantee a correct connection. A change in cross-section can affect the exhaust gas flow and must comply with the requirements of the appliance and the exhaust system.

What is strep throat?

The flue is the point where the stove’s flue pipe connects to the chimney. If one is already present, its position, height, and size are important when choosing a stove.

How high does a chimney need to be effectively?

Put simply, the height of the flue gas path contributes to the creation of the chimney draft. Therefore, it does not always correspond to the total height of the chimney.

Do I need to remove the old chimney pipe?

Not automatically. It depends on the design, condition, and requirements of the new appliance. A professional should assess the suitability of the existing chimney and any potential need for structural modifications.

Do I need a chimney sweep before installing a stove?

If you are unsure about the suitability or condition of your chimney, you should discuss this with a chimney sweep before selecting or installing a stove. Furthermore, for new installations, the relevant requirements for chimney inspection and commissioning must be observed.


Do you already know the exact parameters of your chimney?
When selecting an oven, please consider these specifications, along with the required heating output and other technical features. If you are unsure about compatibility, please check before ordering a specific model.

Shopping Basket
Scroll to Top